I'm with Pierre-andre on this on. I don't think you can better the Cri-Cri in specification or performance. As others have said, the main issue with the design...
... Do you know what the price of these custom props will be? It may be well into $300-400 range for each prop! It would be great to find an existing (model ...
Oleg, you must be talking about http://www.sullivanproducts.com/StartersContent.htm - they manufacture hand-held starters for model planes and boats. I guess ...
In a message dated 9/3/03 12:30:09 PM Mountain Daylight Time, ... Why not put the things in CAD and have a CNC equipped shop do the work? The cost of CNC work...
I like the CAD idea, didn't even think that was possible. I will have to start looking for CNC shop in the Seattle area. As for being a limited manufacturer,...
Wow, this is incredible! It turns out that one of my flying buddies is a general manager at a CNC design and manufacturing facility and is willing to help us...
Stephan, no, I was talking about an in-flight starter. If you look at the same page that shows custom generators, there is a pricture of a custom starter...
Oleg, I did miss that. I thought about starter/generator option and it sounds intriguing. My only concern is - will the gear teath hold okay at continuous...
Dear CriCri-ers! As I mentioned earlier, I found a place with CNC manufacturing capability and had a meeting with them this morning. Their process is set up in...
Unfortunately all my documentation for the new propellors for my CRiCRi was destroyed recently. Does anyone know the specs of the Columban supplied glass (not ...
Hello all. After a long time these pictures are back online. Thanks to my best friend Fabien for the webspace. http://www.stroy.net/cri-cri/index.html...
Hallo every one, Has anyone seen this engine?: http://www.radne.se/Store/Product/ProductDetails.aspx?PartNo=3201 Cheap, strong, low vibrations, low fuel...
Enter your vote today! A new poll has been created for the CriCri group: How much would you pay for copies of the plans and Manual ? o $100 o $200 o $300 o...
CriCri@yahoogroups.com
Sep 15, 2003 1:57 am
1600
My opinion on this engine is the following: - a little bit underpowered. Even though it says that the RPM range is 13,000 and the 12HP is at 9,000, there's no...
Hi Cri-Cri lovers, I have one curiosity, Could be replaced all 2017 alloy for 2024 allo?, sheets, angles, etc. M. Colomban says that there are not any problem...
So far 2024-T3 (Sheet) and 2024-T4 (extrusion) is the only thing I am using. Vic Pedro Molina Luque wrote: Hi Cri-Cri lovers, I have one curiosity, Could be...
Hi All, I'm new to this list and I wanted to provide something to the group so I invited Mr. Cengi Camzi he's a professor of areospace engineering at Pen state...
Enter your vote today! A new poll has been created for the CriCri group: How much would you pay for a kit ? o $1000 o $2000 o $3000 o >$300 To vote, please...
CriCri@yahoogroups.com
Sep 18, 2003 12:33 pm
1605
Enter your vote today! A new poll has been created for the CriCri group: How much does a finish cricri cost? o ~$5000 o ~$10000 o ~$15000 o >$15000 To vote,...
CriCri@yahoogroups.com
Sep 18, 2003 12:35 pm
1606
Hi Vic, I am pleased to hearing from you again, my Cri-Cri is now "growing" after some work (a lot of travels) problems, thanks a lot. I have a 1999 set of...
I have not seen any other type of aluminum in the manual or the plans that are other than 2024. I have, on the other hand, seen some material lists that list...
Hi Pedro, I'm the same as Vic, only 2024. Terry www.cricri.co.uk ... From: Victor Asp To: CriCri@yahoogroups.com Sent: Thursday, September 18, 2003 4:43 AM ...
Hi Terry, It´s nice to meet you, please, update your diary!!!!, good web. The best aircraft of the world has only one problem in this century: low number of...
Greetings All, I am a new member here... Has anyone purchased the CDRom off ebay? And, if so... does anyone have any comments as to the contents? Can a Cri-Cri...
Hi All, I'm fairly new to the list and I'm looking for people in Ontario Canada, that shares my facination for the cricri. I live in Barrie Ontario and will...
Just thought I'd share this information with all who are struggling to find the right bearings for the CriCri. The plans call for GLD4, GLD5, GL6 and GLD6...
The main tires supplied with the Zenair kit I started with are Trelleborg 250-3 and have a 3-1/2 inch hub. Does anyone know where I can find replacement ...
I have been investigating the 3W200 series engines and like what I have seen so far. However, things are getting a bit pricey. I have had discussions with...
Bob, this is good inormation, I had no idea that Sullivan was that expensive. I was planning on using the 3W engines as well. I just got a fax from Cactus...
... Bob, thanks for finding out this information. This is quite depressing! I was really hoping that Sullivan alternator and starter would be a great setup...
