... cannot make reservations for the campground. Does anyone know what the chances are of showing up on Friday and getting a spot? ... Ron, We have gone and...
thanks John, but I got nervous and got a site nearby. http://www.hickoryoakscampground.com/. Ron ... From: johnemcmahon To: Lancair_ES@yahoogroups.com Sent:...
Greg, I'm in the process of ordering the Sierra EFIS for my ES also, and have similar questions. I had been looking under the rear seat on the right side, but...
Greg How about the elevator pushrod tube tunnel. Regards Ron Raby ... From: Greg Campbell To: Lancair_ES@yahoogroups.com Sent: Saturday, July 03, 2004 12:53 AM...
The AHARS needs to mounted as close to the CG as possible. The most popular spot is under the rear seat as far outboard as possible to get away from the flap...
I mounted my Crossbow AHRS under the right rear seat. I have anywhere from a 3-10 degree error and I am not sure why. Kirk Hammersmith at DirectoAvionics and...
... the smaller AHRS ? ... The Crossbow 425EX has an internal magnetometer, basically the same as the Crossbow 500GA. Therefore it is necessary to mount it...
... the smaller AHRS ? ... The Crossbow 425EX has an internal magnetometer, basically the same as the Crossbow 500GA. Therefore it is necessary to mount it...
... GPS was a Garmin OEM unit. Is this supposed to be antenna connection, or is it for something else? Crossbow has built-in an enhancement to the 425EX which...
Attached is a photo of Greg's $4 airplane jack. (A pair of 2x4's stuck in the wing box.) We needed to lift the airplane wheel to check the wheel bearings. We...
Hey Guys, I've been camping for about a week, sorry for the late reply. I had very straight trailing edges coming back from Redmond. But I did run into some ...
I wouldn't pour molten lead into the rudder. I'm not sure what all that heat would do to the composites. I had the same underbalanced situation other guys...
Mike - you made some good points. I don't know where my CG will come out yet - but I have 2 large batteries in the tail already. I was thinking about adding a...
Mike, ET AL I got my kit three years ago and the lead weight I got was a lot larger then yours. If memory serves around 17#. I installed it as is-well not...
Hey Guys, If you installed the bear claw latches with a remote release on your baggage door, I have a good idea that I picked up from Chuck Brenner at the...
For my extra release, I put a ring on the end of a short cable that runs up to the one that goes from my cabin door sill back to the latches. I floxed in a...
to everyone: I am getting ready to install the inflatable door seal. Is there any tring tricky about installing this? something that may not be in the manual? ...
Ron, Just be sure you use an adhesive caulk. I got the wrong stuff and didn't realize the mistake until a couple of days later when we could easily just peel...
thanks, did you rough up the paint? Ron ... From: Skip Slater To: Lancair_ES@yahoogroups.com Sent: Friday, July 09, 2004 11:15 AM Subject: Re: [Lancair_ES]...
We bonded the fuselage top on Wednesday. Wound up using a new can of the new "45 minute" Hysol. (Light Blue vs. Dark Blue). Wetted out with straight Hysol -...
Greg, I love your timing as I'm about three weeks away from bonding on my top (before OSH?). That's a great looking crew of helpers. I planning on using...
Hysol tends to trash clecos - even more so than flox. I didn't have enough clecos - and didn't feel like sacrificing new ones. The screws were cheap &...
Greg and Paul, Great comments Greg. I would add that I did my firewall and the same time. It's a pretty wide gap on my plane so I really had to pile up the...
Greg - Congrats on this milestone!! And thanks for all of the narrative and pictures. They'll help a lot in the near future. Your son looks like he was having...
We are planning to use some surplus tank sealer left over from doing our wing tanks. Would like to do the floor boards and the floor of the baggage ...
I was reading about your idea of thinning the epoxy for ease of application. It may not be a big deal on this but adding thinner will tend to make resins ...
I have a rented house in Oshkosh from Tuesday 7/27 to Monday 8/3. We have the space to accommodate another person, or another couple. The cost per person or...
