Jeff, Thanks for the oil temp update. Was Continental able to identify the problem? Are there other coolers out there with the same problem as yours? -- Or...
The e-mail was in fact sent to the group, so we all should have gotten a copy. The address the message gives for "From", is Ron Galbraith's e-mail address. I...
About 4 months ago, the same thing happened to me. Someone in Europe started sending email using my address with viruses attached to a lot of people. Not much...
AVG free got rid of it easily for me, it did show 2 instances of it, it must propogate instantly. ... From: Harry League To: Lancair_ES@yahoogroups.com Sent:...
Symantec has been slow to spot this one in its current iteration. Here is the site for their take on the issue. Please note that it takes a "Safe Mode"...
try avg it did catch it immediately, although it made me run a full scan but better than cathing it. btw it is free. no affiliations etc. ... From: Harry...
The virus isn't coming from me, but someone on this list does have it, that happens to have my address in their address book. It sends itself out as if it's...
Guys, I just received a set of Lancair aileron weights. Part number 1110 from Kit Components (aerocraft parts). The cost 16.25 each and they look great. 2...
Primer and the matrix resins will continue to shrink and print through. There isn't anything you can do about it and it isn't UV related but additional heat...
I am installing the trim servo in my aileron and am having trouble routing the wires to the outboard end of the aileron. I have the carbon ailerons that came...
I think the accepted practice is to drill through the spar and then fish the wires down the length of the leading edge to the outboard end, where I brought...
Anyone invented this yet?? Cause I could sure use it about now ... You can see my progress in the forum and gallery at www.lancair- builders.com Chat Forum is...
Can you believe I refinanced my mortage and am saving $328 a month? Check it out... http://edgelending.net/?partid=rcc2 If you dont want to be part of this...
Mark - We are also just beginning the wiring process. We plan to route the 4 big fat ones down the right side of the fuselage to 4 5/16" brass studs on the ...
I fished the wire through the existing holes with a piece of safety wire. It took almost an hour of poking to get the safety wire through the holes. I used...
Dan, Any idea how much (what percentage) of the shrinkage would take place in 6-9 months? I wonder if you can minimize the chances of the weave showing...
John, What you are doing sounds exactly like my setup. All the fat wires and things like flap motor, nav, , overhead wires, and strobes down the right. My #2...
Mike - What did you use for the ground lug in the rear? We are running a couple of LED lighting fixtures in the baggage and battery compartments off of the #1...
John, I used B&C's smaller ground block mounted to a piece of phenolic. It's the same phenolic on which I mounted fuseblocks for battery buses and a few other...
Hi Mike I don't know how much shrinkage you get from a mostly cured part as it cross links further but polyester/vinylester shirnks about 9% by volume and...
I also bought my stuff from B&C. I have the 48 lug ground on the inside of the firewall. I cut one of the 24 lugs in half, half is in the rear (photo ...
John, All of my batteries and power distribution grids, solenoids, etc are in the tail. For a ground I floxed a 2.5" X 5/16" steel bolt threaded 100% into the...
Attached are some photos of how I did my wiring. I have MANY more! Feel free to contact me at your convenience. Basically, I mounted two 17 amp hour...
I suppose most of you have probably heard by now, but Chuck Brenner was killed yesterday in Texas while flying his LNC2. He and his family was staying in TX...
We met both Chuck and his wife at Sun N Fun a couple of years ago. He was showing the extraction exhaust he proposed for the IO-550. We ended up buying one of...
Chuck Brenner's Memorial Service is scheduled for Friday 9/17/04 at 10:00 AM at: Assumption Catholic Church 901 Roseland Houston, TX 77037 phone(281)447 6381 ...
