Who ever sent me the photo’s, thanks for sending them, the fly-in seems like it’s a lot of fun, however, what I really want to own a lancair but it seems...
Mike Too bad I can't open the pictures. Would have liked to see them. Gene Underland - Minnesota ... From: mikeeasley@... To: Lancair_ES@yahoogroups.com ...
Mike - There were no pictures of the Redmond ES's attached to your email. Could you re-transmit them? Thanks, John On Wed, 3 Sep 2003 11:20:12 -0500, Gene...
The use of fully and partially threaded cap screws (no proper grip length) furnished by Lancair seems to be a problem for some folks on this list - Ron and Me...
Sign us up John! Sounds like a good solution John McMahon Lancair Super ES builder ... From: John Schroeder To: lancair_es@yahoogroups.com Sent: Thursday,...
Robert - The -20's are the longer ones and are sized to accomodate the thickness of the tow plate. We did not have to ream the holes in the tow plate to ...
Please put me on the list also......Dave Watermann....Hampshire Ill. ... From: Don Parsons [mailto:dap@...] Sent: Thursday, September 04, 2003 11:08...
I'll take a set! Cliff Hoover, Arlington, Texas 618TS Reserved ... length) ... list - ... grip ... point ... them. The ... like to ... sets. ... length of ... ...
John: Not exactly sure what is going on, but if I am going to run into this problem when installing my nose strut, I'll join the group for a set. Ed Silvanic ...
Hi guys - Great response to the bolts. Don Parsons: the -20's would be for the front two bolts - the ones that hold the tow bar plate on. The other two would...
John, I couldn't find the data for this bolt in my catalog. Maybe I have an old catalog. I did find a hex socket head bolt that can be had with a lockwire...
Hi Mike - Did you get the .TIF file attached to my original email? It is the top part of the first page of the bolt's description from their catalog. Attached...
Ed - Lancair has gone to cap screws and nutplates to secure the nose gear fork to the strut. This makes the installation of the nosewheel pant a whole lot ...
John, The MS20005-17 and -20 bolts are around $17 each from Genuine Aircraft Hardware. Ouch! I would like to join the group for a set of the 12 point bolts. ...
Fellow ES Builders, I have been researching these bolts and have the following prices MS21250-05018 Bolt Qty of 20 $2.50ea. MS21250-05020 Bolt Qty of 20 $4.55...
Bryan - We are up to about 11 or 12 guys who want the bolts. Good prices that you quoted!! I talked with Tim Ong this morning and he wants a set!!! He flinched...
All of the bolts are in stock and are factory new not military surplus. I guessed at 20 each but it sounds like many more could be ordered. The price will be...
Bryan - Many thanks for the info. The -017 and -018 are about the same. Both are candidates for the aft bolts. We checked the grip lengths and overall lengths...
John: Put me down for a det of the nose bear strut bolts. Let me know when and where to send the money. Eugene Long Lancair Super ES glong2@... ... ...
I couldn't tell from the picture of this bolt, but typically the "high strength" bolts have a radius under the head leading to the shank. If these have that...
Greg, The MS 20005-XX bolts were 160 kpsi tensile, 96 kpsi shear. And I checked to see about any required special washer and there is such requirement with...
Greg - I couldn't tell either, but in the catalog, they showed a column with the required washers and/or cotter pins for several other bolts. I asked Tim in an...
Put me down for a set of the bolts. I'm not in any particular hurry. A month or two is fine. I looked at the PDF file of the bolt drawing (viewed at 800%)...
