BSA email list "Guidelines for Use"... sent automatically on joining, and each month thereafter This list was created for the FUN, enjoyment and benefit of ...
bsa@yahoogroups.com
Mar 1, 2004 10:04 am
20944
... I also don't get any charge on my bike, but the dyno is putting out lots ... it is the ... want to ... So, in your case, does power reach the output...
Dear all, Given that I dont ride in the dark this is not a huge problem. My dynamo does not work. I have three dynamos and I have done a motopr test on them...
... 1 Volt would be typical of a dynamo with no live field coil. Did you do the test with the D and F terminals connected together? That should give about 12V...
I need a new alternator rotor for my 1967 A65T. Genuine Lucas ones with a welded core cost aroung £80 UK, whereas a pattern part (e.g. Wassel) cost around...
... you ... Had a similar problem last year with the Flash- 1 volt on the meter. Before giving in & spending beer tokens on a rewind I checked the brushes &...
The dynamo didn't work on my M20 when I bought it. I invested a few pounds in new brushes and hey presto - the ammeter swung over immediately. Very ...
HI I tested my Mag/Dyno again tonight(connected F & D terminals together connected a multi meter set to 20Volts DC, Negative to the link wire positive to earth...
66'250 c15 The motorcycle does not use a battery. I've got fuel to the carb and now the tickler works, the plastic float needle was upside down...with kicking...
Jake, When was the last time this bike was started? Make sure you have a spark. If so get some starting fluid take off the air cleaner and spray it in the carb...
... I see a spark from the plug? I was told the motorcycle was started about a month ago. ... spark. If so get some starting fluid take off the air cleaner and...
Jake, Pull the plug and lay it against the head so the large nut on the plug is touching metal (the head). When you kick it over you should have a spark...
- ... policy. ... steep ... Sportster, ... Hi Ray, Are you a member of the BSA Owners' Club? If so, tell Footman James because I believe that the club has...
... An important point which may not be apparent from the above is you DON'T hold the plug, cap or lead against the engine when kicking the bike over. If you...
The small rollers in yor clutch centre, they are not all the same length, and should be. This took me weeks to find on mine! Andy Lorenz ... From: Paul Evans ...
... plug from another motorcycle...the spark does not seem intense? At this point I'm going to re-check all elect. connections. The Amal carb does not have a...
... the Kent branch meetingss the kids are big enough to look after themselves for a couple of hours on a Thursday now. (Yes I know I can go there in a car but...
Jake, When was the last time this bike was started? Make sure you have a spark. If so get some starting fluid take off the air cleaner and spray it in the carb...
... I'm going to check out the carb further now that I have some what of a spark...I think something is clogged because I don't smell fuel after pulling the...
Where are you situated? how much of a hurry are you as I may know someone that may be able to re magnetise it . Club night tonight I will ask and let you know ...
Just had a word with my man on dog & bone unable to do as too many poles for his equipment.But he is surprised that it is no good has it been in a fire or had...
We would like to remind you of this upcoming event. South Cheshire BSAOC Club Night Date: Thursday, March 4, 2004 Time: 8:30PM - 11:30PM GMT Meet at The...
bsa@yahoogroups.com
Mar 2, 2004 8:33 pm
20969
... screw are removed will the jet block pull straight up? My Rupert Ratio manual showed up today so at least I can start to understand how this carb fits...
Hi all I finally worked out how to get the Dyno off of the Mag (Simple I know if you've done it before) cleaned up the commutator and reassembled connected up...
... From: "ektin2001" <americanthunder@...> To: <bsa@yahoogroups.com> ... fire ... fireman ... With strong credentials like that, I certainly will not...
95% of dynamo faults are due to faulty (previously overloaded) armatures. To test one properly you need a growler. To test a dynamo properly you need a test...
