Hi Pierre, I have done this also, power coating my top yokes completely. I had to scrape all the power coating off from the inside taper, back to the bare...
BSA email list "Guidelines for Use"... sent automatically on joining, and each month thereafter This list was created for the FUN, enjoyment and benefit of ...
bsa@yahoogroups.com
Jun 1, 2005 8:01 am
28336
A7/ 10 family I think EA was the 1956&7 seasons and FA was 1958&9, so that frame would either be late 1955/ early 1956 or late 1957/ early 1958. EA frames used...
Thanks Andy. I have done this...removed all traces of paint.....is it now supposed to fit flush with surfce of tripple tree or is it normal to have a 1/8 inch...
Hi, I have an alternator on my B40 which has non-standard colours coming from it. Is there any way that I can tell which should be which to the correctly ...
Hello All, I first want to thank you all for your continuing support that you already have given Bulbsthatlast4ever. All good things must come to an end at one...
Pierre, I was under the impression that a service tool is needed to draw the taper into the top yoke (tripple tree) although I've heard some people use a broom...
Hello eveyone, I announced that I wanted to get my Goldie back on the road earlier. Not sure right when, but I'm starting. Problem #1 My Cam spindles locate...
John, I did not need a broom handle as I assembled once the the yoke, top and bottom tripple tree were in place with bearings secured on the bike. So all I did...
Hi Frank. Loose cam spindles IS a problem, that must be addressed. If you look carefully the spindles have a relief spot on them to allow the tappet to fully...
In late March I had located a fellow by the name of John Grieves who was/is part of the BSA yahoo group. He had offered me to send a piece of A50 unit twin...
Could be Greg but I suspected they were CAD and John Mead confirmed. I have been ordering quite a few nuts and bolts from BritishOnly and all are CAD. Zinc...
On second look, it appears that the front is all hard chrome and the rear is part hard chrome (shaft) and cad exterior bell shaped end and sleeve......but I...
Hi Pierre, 1/8" beneath the top of the fork yoke sounds ok, remember if it was flush, then once the top nut had been tightened, the taper would not be fully...
Buy the correct tool, a universal one (with multiple heads) is only £15 ish. Using a broom handle, you need to pull the stantion high enough into the top...
You can make a fork puller by turning down a fork top cap, drilling a hole through it and inserting a piece of threaded rod. Fit a nut either side of the fork...
Hi, Are ther any staic Dc checks that help me identify which winding is which on the B40 Alternator ? The 3 wires coming away are non-standard colours. If I...
what are the colours? ... From: bsa@yahoogroups.com [mailto:bsa@yahoogroups.com]On Behalf Of jet_morgan2000 Sent: 02 June 2005 07:46 To: bsa@yahoogroups.com ...
... From the Alternator the three colours are Orange ... Green ... Yellow. From the Harness the three colours are GreenYellow ... GreenWhite ... GreenBrown (...
For those of you with access to Maplins Electronic Store they sell a GIANT Red LED cluster about 3/4 inch in diameter which has a total of 6 led's in the same...
Hello Peter, The stator is open as I can clearly see the windings etc. I assume the encapsulated type is just like a block or resin or similar ? Brian Moore. ...
Brian,
It seems that you may have a Wipac stator instead of a Lucas type.
Your loom uses standard Lucas colours.
I would recommend using a Lucas type stator...
They are cad plated steel, period. I know because I handled and sold them when I worked at a BSA/Triumph dealer back in the 1060/70s. John Mead ... ...
