Reminder from the Calendar of bsa http://groups.yahoo.com/group/bsa/cal OPEN DAY East Sussex Branch BSAOC Sunday September 3, 2006 12:00 pm - 4:00 pm (This...
bsa@yahoogroups.com
Sep 1, 2006 11:56 am
33326
Just trying to clear something up . Could or should my 69 lightning motor have the clutch cable in the back of the motor? I have determined that it should be...
Taht's it, I've had enough of Bantams. I 've got a D13 Sport, D14 Sport (both with V5C's) and a D7, all for fettling/restoration. Anyone interested ?? Phone me...
On Fri, 1 Sep 2006 13:09:33 -0400 ... Hi Wade, They went to the cable thru the top in 1970. Both setups work just fine. The top feed is a ball and ramp setup...
On Fri, 01 Sep 2006 19:21:03 -0000 ... Cyril, About the Bantams...Thanks but No thanks. Of all the A65's the spitfires seem to have the worst reputation for ...
... for ... most ... The reason for my A65 blowing up the first time was because a previous owner had overightened the pressure releif valve in the timing...
BSA email list "Guidelines for Use"... sent automatically on joining, and each month thereafter This list was created for the FUN, enjoyment and benefit of ...
bsa@yahoogroups.com
Sep 2, 2006 12:00 pm
33332
Hi Chris: My A10s and Goldstars have an O ring on the speedo drive shaft housing that seems to harden over time and leak. Before sliding the newly applied...
namelypigs@...
Sep 2, 2006 1:57 pm
33333
In a message dated 9/2/2006 4:22:02 AM Pacific Standard Time, ... OK, there are two versions of speedo drive housings... the early one is brass and has a large...
Hello all, Does anyone in this group know how many 1971 Firebird Scramblers were built? I have a very nice original with 4600 miles, that I'm planning to sell...
Hi Ted..Sorry I didn't make it to your camp...I have been decorating the living room and I didn't get on as well as thought I would, so I had to finish it off...
Johnonefab@...
Sep 3, 2006 11:17 am
33336
Hi Folks...I had a problem a while ago...Oil was dripping under the bike...It always does but this was more than usual..so I looked to see what the problem...
Johnonefab@...
Sep 3, 2006 11:27 am
33337
You have over-filled the gearbox. A pint is 600cc, but the gearbox capacity is 400cc. You can drain off any surplus by removing the "level" plug at the rear of...
you may not believe it John but it's called heat shrink sleeve (:-) brilliant stuff though and looks like you found another use for it All the best - Bill ... ...
The relocation of the clutch cable to enter the case from the top was in 1970 Greg Donald 48 Miriyan Drive, Kelso NSW 2795 Tel: 02 63317290 Home Tel: 02...
Sorry you couldn't make the camp John - I guess there were quite a few loaded up bikes round the country that never hit the road due to the rain! We had about...
The RHS rear wheel bearing of my WDM20 1942 packed up yesterday in the middle of the N. Yorks Moors. Where is the best place to buy bearings from and the cost...
Hi there I was wondering if anyone could tell me what the letters stb stand for on a pre unit gearbox? It is not a standard gearbox marked std . Its STB-T for...
Thanks for the info on the stb. I was wondering if theres a good website to read about what all these ratios mean stb, rrt, asct, close ratios vrs. wide and...
Hello All, I am with Sully, I am going to be putting together a gearbox (*plunger A10 gear box) and would greatly appreciate diagrams, tricks..do's and don't...
I've recently bought 2 b25 bikes (actually a tr25w & a non running b25). I've never seen another one run. When I first got it, the bike kicked back badly when...
See how much fun we had at the International BSA Ralley 2 weeks ago. Brimfield Mass. had some nice back roads and great scenery for our daily road trips. Great...
rings and a hone and your tr will be good as new..... probably some scadge gunk in the carb you will want to track down. cgbusch <cgbusch@...> wrote:...
I use City Seals and Bearings in Sheffield / Rotherham. ... From: "jet_morgan2000" <jet_morgan2000@...> To: <bsa@yahoogroups.com> Sent: Monday,...
Gordon Brown
gordon.brown@...
Sep 5, 2006 7:02 pm
33354
Hi James, I took apart and put together an spare gearbox for my plunger A10 and put some pictures and descriptions on my web. They may or may not be of use....
